10 Kw Generator
Does anyone know how to fix a problem on a 10 Kw generator where it won't generate power to the convenience receptacle or give out a reading on the A.C. Volts meter? It does once I hold the master...
View ArticleM1085A1P2 Cab Hydraulics
I've got an issue with the cab hydraulic system on the M1085A1P2 variant. I've replaced the manual hydraulic bank as that's what my troubleshooting led me to. After replacing it, I still cannot get...
View ArticleM1097 Oil Cooler Line
Have a 1097 that keeps blowing off the dexron line to the cooler. No real pattern in it for behavior it's happened multiple times. Done a long road test and no issues then go to take back to unit and...
View ArticleSustainement Brigade Questions
I have now been the Senior Maintenance Analyst for my BDE for about two weeks and I have been tasked with standing up the CMDP program for the brigade because it doesn't have one, with that I know I...
View ArticleService Engine Light
We have several M1078A1 LMTV Cargo Trucks that the service engine light will not go out on them. We have followed the troubleshooting charts and reset the codes, but the light keeps coming on. Does...
View ArticleHow To Update A Service Packet Using Html
can someone please help me on how to update a service packet using HTML. I'm new to the motorpool side and always worked at the SSA. I am the only clerk that was sent overseas from our home station. TIA
View ArticleFmtv Allison Md 3070 Transmission
Does anyone have the TM for the Allison MD 3070 transmission.
View Article15Kw Under Voltage
15kw undervoltage light comes on when generator starts. However I can hold the master switch in the start position and the generator will go to 60hz and put out power.
View ArticleClik here to view.
Husky Height Lift Actuator Repair
ALL, Has anyone tried to repair a HT/ Lift actuator for the husky mine detection arms? I have several Huskys and they're staring to come into the shop with the same actuator fault (Not lifting). I tore...
View ArticleM916A3
All, One of my techs is performing a service on an M916A3. When it comes to the front hub service the special tools for it either have NO nsn or cannot be purchased through the system. TM...
View Article3Kw Pma Removal Issue
Eyyy, greetings from Wiesbaden, Germany! So, I've got a MEP831A that's being a bit of a pain. We're in the process of removing the Permanent Magnetic Alternator (PMA), we have the Stator removed,...
View ArticleLtas Windshield Wiper Blades
I'm looking for a good NSN on wiper blades for the LTAS the TM only list them with the B kit?
View ArticleLtas Schematic Job Aid
Community, I work at Oshkosh Defense and am working on an NSN for a schematic job aid. Basically a compilation of drawings of all the electrical, hydraulic, and pneumatic schematics needed to...
View Article2Kw Generator Won't Start
I have a 2kw MEP-531A generator that was brought into the shop because it wouldn't start. So far I have replaced the fuel injector and gasket inside the cylinder head and replaced the O-rings inside...
View ArticleNsn For Bastlic Door Window
The NSN I got for the MSD where a little too thick and doesn’t fit.
View ArticleNeed Troubleshooting Steps For Ctis
I’m having problems with the CTIS system. I got one truck that will not build up air pressure or have air leaks but later on the week work fine.
View ArticleM915A3 Windshield Washer Nozzle
looking for nsn for the windshield washer nozzle located in the wiper arm
View Article10Kw Generator Won't Provide Power
I have a 10 Kw TQG MEP-804A generator that will not provide power to the convenience receptacle and will not show any volts on the voltmeter. The generator turns on but does not show any volts or...
View ArticleMep-813A
I have a generator that isn't producing power. K1 relay is fine, K15 relay works, AC voltage from Magnetic pickup to Crank Disconnect Switch is within range (2.4 VAC). What I am trying to find is the...
View Article